资源中心 / 技术文章
面向湿度控制决策的技术文章
浏览面向农业、能源、电气与工业环境的应用说明、工程解释、设备对比与实用指南。文章正文目前为英文。
您可以先通过文章理解具体问题，再返回资源中心查看案例、产品资料、企业视频和项目准备信息。
从问题背后的运行工况开始。 可按应用场景、湿度风险、设备类型、安装条件或技术主题搜索。
按文章主题浏览
从应用场景或设备工况开始
01
农业与可控环境
面向温室、室内种植间、干燥空间与仓储环境的应用说明与选型指导——在这些场景里，湿度影响的是作物本身，而不只是空间舒适度。
浏览文章 → 02工业除湿
覆盖冷冻、吊顶、转轮与低露点设备的对比与工程说明，以及决定它们取舍的运行工况。
浏览文章 → 03储能与电气环境
面向电池储能、柜体、集装箱与开关设备的露点、结露风险、紧凑安装、控制与验证指导资料。
浏览文章 → 04商业与建筑湿度控制
围绕结露、水损、干燥、防霉，以及商业空间和建筑湿度问题中的设备选择提供实用说明。
浏览文章 → 05加湿与空气质量
围绕加湿、通风、过滤、湿度测量，以及湿度控制与整体空气系统的协同关系提供技术文章。
浏览文章 → 06湿度科学与工程
解释相对湿度、露点、结露、湿度测量、监控与控制，帮助理解工业湿度控制中的关键判断。
浏览文章 →技术文章库
搜索和筛选与当前工作最相关的技术主题
每篇文章都在技术文章库中有明确入口，并关联相关行业、产品系列、案例和项目支持。
找到合适的资料
搜索文章标题、摘要、分类与技术主题。文章内容为英文，建议使用英文关键词。
在资料库中搜索。
Commissioning and Validation Checklist for BESS Humidity-Control Equipment
Commissioning a BESS humidity-control device means proving more than “the unit turns on.” The installed system must move air through the intended zone, remove moisture under the relevant condition, drain safely, report useful status and recover after a defined moisture event.
Condensate Drainage for Battery Cabinets and Containers
Condensate drainage is part of the dehumidifier installation, not an accessory decision to make on site. A correctly selected unit can still wet a battery cabinet if the tray is not level, the hose rises, the outlet freezes, the termination allows backflow, or the enclosure penetration is poorly…
Connecting Dehumidifiers to BMS and EMS
Connecting a dehumidifier to a BMS or EMS starts with a signal and data list, not with the phrase “RS485 required.” RS485 describes an electrical serial layer. It does not define the register map, alarm meanings, command authority, update rate or commissioning test.
How to Diagnose Condensation in Battery Cabinets
Diagnosing condensation in a battery cabinet or BESS container starts with two traces on the same time axis: internal dew point and the temperature of the coldest suspected surface. Water forms wherever the surface trace reaches or falls below the dew-point trace. The rest of the investigation id…
BESS Container Dehumidifier Sizing: Required Inputs
A 20 ft or 40 ft BESS container does not have a standard dehumidifier capacity. Container length describes the outer boundary, not the moisture load. Two containers of the same size can require very different equipment because their free air volume, ventilation, door use, internal temperature, cl…
Heater, Ventilation or Dehumidifier for Enclosures?
Choose an enclosure heater when one or a few surfaces need to stay above dew point. Choose ventilation when the incoming air is demonstrably drier and airflow serves a defined purpose. Choose active dehumidification when the enclosure's moisture content must be reduced across changing temperature…
BESS Container Condensation with AC: Causes, Checks and Control Boundaries
A BESS container can develop condensation even when its air conditioner is operating. Cooling controls air temperature and may remove some moisture, but it does not guarantee that every local surface remains warmer than the dew point of the air touching it. Moisture entry, cold surfaces, airflow, cy
Greenhouse Humidity Control: How to Diagnose the Load and Choose a Control Route
Greenhouse humidity control should begin with a moisture balance, not an equipment list. Identify where water enters the air, when removal becomes insufficient, and which crop or structural surfaces approach the local dew point. Only then can ventilation, heating, air movement, and mechanical dehumi
Ventilation or Dehumidification for a Greenhouse? Test the Conditions First
Ventilation and mechanical dehumidification are not universal alternatives. Ventilation can remove water when the incoming outdoor air is drier in water-vapor terms than the exhaust air. Mechanical dehumidification becomes relevant for the remaining duty when outdoor air, heat loss, CO2 retention, w
Humidity Control in Battery Cabinets and Enclosures: Why Condensation Is the Real Design Problem
Most humidity problems in battery energy storage are not humidity problems. They are surface temperature problems.
How to Define Dew Point Control Conditions for Battery Enclosures
Dew point control for a battery enclosure should be defined around the coldest relevant surface and the moisture condition of the air touching it. The control specification must also state where the air is measured, how measurement uncertainty is handled, and which operating transitions are included
Water and Mold Damage Restoration: Causes, Cleanup, and When to Hire Pros
Water and mold damage restoration involves eliminating water, drying the affected structures, and addressing mold in order to restore a building to a safe, functional condition.
没有匹配的资料
试试更宽泛的关键词，或换一种方式描述应用。
可以按设备类型、湿度问题、行业、安装条件或技术主题搜索。
应用这些信息
需要把文章内容应用到具体项目吗？
请提交应用场景、运行工况、目标和安装限制。我们可以协助梳理在产品选型或工程评审前需要确认的问题。
沟通项目需求